3dm test ramp
Moderators: Jani Soderhall, Henry Hester
-
- 1953-2010 (RIP)
- Posts: 141
- Joined: Thu Aug 22, 2002 2:00 am
- Location: San Luis Obispo
- Contact:
<img src="http://www.3dm-sport.com/images/3dm-tra ... 0.jpg"><br>
We just completed our first attempt at a start ramp. Just under 4 ft tall, 3 ft wide, 4 ft deep platform. Probably used $150 in materials, but did not keep track of the time. It's somewhat heavier than the Airflow ramps, but similar in construction.
We just completed our first attempt at a start ramp. Just under 4 ft tall, 3 ft wide, 4 ft deep platform. Probably used $150 in materials, but did not keep track of the time. It's somewhat heavier than the Airflow ramps, but similar in construction.
-
- 1953-2010 (RIP)
- Posts: 141
- Joined: Thu Aug 22, 2002 2:00 am
- Location: San Luis Obispo
- Contact:
Hard to say. We do have a modest roll-in at the top, and the bottom transition is similar to FCR, but otherwise straight. This ramp is a fair bit taller and steeper than FCR, but it's not particularly scary. The FCR "s" transition does provide perhaps a bit better platform for a launching pump toward the bottom.
I'll bet there are craftsmen in your part of the world who are far more competent in building something like this. All I had was a photo and a vague recollection of how other ramps were constructed, and this came out okay.
I'll bet there are craftsmen in your part of the world who are far more competent in building something like this. All I had was a photo and a vague recollection of how other ramps were constructed, and this came out okay.
-
- ISSA President 2011-2024
- Posts: 4656
- Joined: Thu Aug 22, 2002 2:00 am
- Location: Sweden, lives in France
- Contact:
I like both straight and S-shaped ramps. I'm not sure it really makes a difference. But it is important to have a good transition at the bottom for the straight ramps, so that you don't hit the bottom at too much of an angle. I'm sure the S-shaped ramps accomplish this task better.
At the top the main thing is not to make the slope too steep as longer boards may scratch the edge going down. Once again, S-shaped ramps may be better at that.
The most important factor for all ramps in my opinion is to stay put. Ie when you pull away, the ramp mustn't move. This can be accomplished by making an overall heavy ramp, but the easiest way to do it is probably to make a long enough platform up on the top.
I'm a bit surprised that the rear legs are not connected in any way to the other legs. If they would be connected, even with a very weak piece, they'd hold together better if you need to move or slide the ramp a few feet.
I critisized the ramps in the tunnel race which were too light, but the once in Gruningen were OK, so Chris Hart probably made little improvements in the construction to make them more stable.
For racing it's good to have a few steps behind the ramp, to get up easier. It speeds up the "getting ready" phase during practice and while racing.
At the top the main thing is not to make the slope too steep as longer boards may scratch the edge going down. Once again, S-shaped ramps may be better at that.
The most important factor for all ramps in my opinion is to stay put. Ie when you pull away, the ramp mustn't move. This can be accomplished by making an overall heavy ramp, but the easiest way to do it is probably to make a long enough platform up on the top.
I'm a bit surprised that the rear legs are not connected in any way to the other legs. If they would be connected, even with a very weak piece, they'd hold together better if you need to move or slide the ramp a few feet.
I critisized the ramps in the tunnel race which were too light, but the once in Gruningen were OK, so Chris Hart probably made little improvements in the construction to make them more stable.
For racing it's good to have a few steps behind the ramp, to get up easier. It speeds up the "getting ready" phase during practice and while racing.
-
- Germany
- Posts: 503
- Joined: Mon Sep 09, 2002 2:00 am
- Location: Germany
- Contact:
I think the curved transitions are better because you can really get a "pump" while rolling down. The angled transitions make that harder. It may be an advantage for transition oriented skaters, but on the other hand everyone can learn that.
The FCR ramps were too low in my opinion (for Morro, not for Avila)
The FCR ramps were too low in my opinion (for Morro, not for Avila)
-
- 1953-2010 (RIP)
- Posts: 141
- Joined: Thu Aug 22, 2002 2:00 am
- Location: San Luis Obispo
- Contact:
Here's a side view showing the transition and side bracing ...
<img src="http://www.3dm-sport.com/images/ramp300.jpg">
<img src="http://www.3dm-sport.com/images/ramp300.jpg">
-
- Slalomspot.com
- Posts: 584
- Joined: Wed Jun 18, 2003 2:00 am
- Location: North America
- Contact:
-
- 1953-2010 (RIP)
- Posts: 141
- Joined: Thu Aug 22, 2002 2:00 am
- Location: San Luis Obispo
- Contact:
I am sure we have craftsmen in this part of the world that could build starting ramps. The thing is is that no one has a place to build/store it and then no one can schlep the thing around.
nice ramp though!
I prefer the gate free design over the FCR style gate. I'd rather have a wand start like ski racing anyway.
nice ramp though!
I prefer the gate free design over the FCR style gate. I'd rather have a wand start like ski racing anyway.
-
- ByrdDog
- Posts: 227
- Joined: Wed Sep 18, 2002 2:00 am
- Location: Madison, Mississippi
Nice ramp Howard. Looks like it would be lighter than my design but there is something to be said for the extra weight. That was the reason for the two piece design along with making it fit in the back of an F-150. I would imagine yours sits better on a less than perfect surface. Mine tends to rock a bit and require shimming. If I do it again I would like to add screw type adjustable "feet" on the bottom.
-
- 1961-2013 (RIP)
- Posts: 3279
- Joined: Tue Aug 27, 2002 2:00 am
Ricky,
Do you have pictures of yours other than race day stuff? I don't think I've ever seen a good photo of your construction other than from a distance as in when a race is starting or some such thing.
I know: "Wes, why don't you just come to Mississippi for a race and see it for yourself?" Hey, I'm workin' on it! The only thing keeping me from heading to Jackson is time, money, skill and more money. :razz:
Do you have pictures of yours other than race day stuff? I don't think I've ever seen a good photo of your construction other than from a distance as in when a race is starting or some such thing.
I know: "Wes, why don't you just come to Mississippi for a race and see it for yourself?" Hey, I'm workin' on it! The only thing keeping me from heading to Jackson is time, money, skill and more money. :razz: