foot blocks and such-need advice

A Forum For New Racers.

Moderator: Karl Floitgraf

Post Reply
Liam Thornton
Posts: 9
Joined: Tue Mar 31, 2009 6:08 pm
Location: west hartford, CT

foot blocks and such-need advice

Post by Liam Thornton » Wed Apr 01, 2009 6:59 pm

I am relatively new to slalom here but my question really pertains to longboarding in a way-sorry. I'm looking for help with making a long foam convex rail in the back half of my board so that when rolling my foot over in drifts and deeper carves, i can have something to lock the arch of my foot (heelside) and my toe (toeside) into. as you can see it is sort of a longboarding question because I would be putting this on a longboard, but slalomers will probably know better how to make something like this. any help is greatly appreciated.

Stephen Lavin
Topsider
Topsider
Posts: 339
Joined: Sun Mar 19, 2006 5:50 am
Location: Chicago, Illinois
Contact:

Post by Stephen Lavin » Wed Apr 01, 2009 9:42 pm

http://www.sk8kings.com/Merchant2/merch ... ry_Code=WR

Take a look at these wedges that you can lay grip tape over. Will allow for minute corrections in footing on the fly without a "hard stop" like a toe block or rail. Might help you get the freedom you're looking for while riding.

here is a link that shows a slalom deck with this stuff applied (although if I am understanding you correctly you may be applying this somewhere in the median??):

http://www.slalomskateboarder.com/phpBB ... ight=block

Hope this helps out!

LAVIN
LAVIN

Liam Thornton
Posts: 9
Joined: Tue Mar 31, 2009 6:08 pm
Location: west hartford, CT

Post by Liam Thornton » Mon Apr 06, 2009 5:19 pm

yes thank you I took a look in this thread earlier and at least found out what kind of material would be good to use, but yes you are correct this will be going in the median more like the back of actually a loaded vanguard so as to fit the arch of my foot when it is being rolled forward (back knee down).

Toby Warg
Posts: 193
Joined: Wed May 02, 2007 4:43 pm
Location: Umeå, Sweden
Contact:

Post by Toby Warg » Mon Apr 06, 2009 6:30 pm

Something like the gas pedal here?
http://www.rogers-bros.com/index.php/accessories

Liam Thornton
Posts: 9
Joined: Tue Mar 31, 2009 6:08 pm
Location: west hartford, CT

Post by Liam Thornton » Mon Apr 06, 2009 11:44 pm

that looks like something I could get some use out of yes, and I may pick one up just for the heck of it. what I'm trying to make will be useful for both toe and heelside drifting and carving however. Its hard to just describe stuff like this over the internet but picture like an elongated bulge running from the back truck to just before about the middle of the deck , I think thge new rayne hellcat has something like it but they call it the pleasure dome and it is very long, a generic shape where as mine will be shaped to my own shoe and covering only about a quarter to a third of the deck. no worries the more people reply to this the sicker it will be when complete as I can use a little of each of your ideas. thanks guys

Toby Warg
Posts: 193
Joined: Wed May 02, 2007 4:43 pm
Location: Umeå, Sweden
Contact:

Post by Toby Warg » Tue Apr 07, 2009 12:19 pm

Something like this Sec9?

Image
Image

Liam Thornton
Posts: 9
Joined: Tue Mar 31, 2009 6:08 pm
Location: west hartford, CT

Post by Liam Thornton » Wed Apr 08, 2009 12:50 am

exactly exactly precisely what I was talking about. how did you make yours if you will share your secrets?

Toby Warg
Posts: 193
Joined: Wed May 02, 2007 4:43 pm
Location: Umeå, Sweden
Contact:

Post by Toby Warg » Wed Apr 08, 2009 5:00 pm

It's not mine, but Erik Lundberg's. I'm 99% sure it's made by Sector9 and that it probably will be out soon.

Liam Thornton
Posts: 9
Joined: Tue Mar 31, 2009 6:08 pm
Location: west hartford, CT

Post by Liam Thornton » Wed Apr 08, 2009 5:25 pm

well I don't need the sec 9 so badly as I just need something like whatevers under the grip on it, does anyone have any good ideas of how to make one?

Post Reply