typical Turner board setups

Turner Summer Ski Slalom Boards

Moderators: Christopher Bara, Peggy Turner

Seismic - Bad ass slate technology

typical Turner board setups

Postby Howard Gordon » Thu Sep 05, 2002 7:52 pm

Image

Here are some typical setups for Turner boards. Note that these are my personal boards, though my kids' (Lauren and Dylan) boards are set up almost identically, as are a number of other Turner team rider boards. If any other riders want us to host their board setup photos, let me know.

Turner Fullnose

Image
Image

Medium-stiff low camber fullnose built by Vince. Tracker RTX in front, Turner TTC 101 in rear, Cambria 86's in front, Cambria 82's in rear, Turner Abec 7 bearings around. Note a small amount of wedging in front and back using a full 1/8" urethane pad plus about 1/3 of another 1/8" pad to create a 3-4 degree wedge.

Image

Trucks are mounted using stainless hex buttom cap 10-32 screws with rubber lined steel washers to protect the top gelcoat.

Dylan's board is identical in setup, though he has a yellow fullnose that Vince was able to build with extra soft flex, and he rips with this board (he took down Breamo at La Costa with it in first day elimination round). We typically pracice 5 - 6 ft straight and offset courses with these decks.

Turner GS/Hybrid

Image
Image

This board is typically set up with trimmed Avalon 85's front and 80's rear, Turner Abec 7's, Seismic 110 in front with silver springs, Turner TTC 101 in rear, same wedging as the fullnose but with one additional 1/8" riser in front and back because of the larger Avalons, and same stainless hardware, but without the washers. Dylan and Lauren run RTX's in front instead of the Seismic, and generally run with Cambrias instead of Avalons for somewhat better traction and speed control. This is actually Lauren's board for 5 ft tight through big GS, though she'll often remove the spacers and tighten down the bearings on steeper courses. This setup, with minor variations, is far and away the winningest combination on the FCR tour (at least 5 pro division wins !).

Turner GS/Hybrid XL - "fatboy"

Image
Image

This is far-and-away my favorite board, with Seismic 135mm w/silver springs in front and Turner TTC 101mm in rear, wedged the same as the hybrid. For practice, I generally run untrimmed Avalon 85/80 combo with Turner Abec 7's, though at Hood River I ran trimmed Avalon 85/80's, and in the La Costa GS I ran Cambria 82's front and 78's rear (soon to be in production) and had outstanding traction. I can run courses as tight as 6.0-6.5ft or wide open as the La Costa GS.
Howard Gordon
1953-2010 (RIP)
1953-2010 (RIP)
 
Location: San Luis Obispo
Posts: 141

Postby Adam Trahan » Tue Sep 10, 2002 11:26 pm

Image

Ahh, my 2nd Gen white cutaway with a "stiff" flex profile.

Flat riser Seismic 110mm "hollow axle" front, rear urethane wedged back attached with stainless steel cap hex head/sealing washer hardware.

Stinger wheels (soon to be changed to Cambrias), Oust Moc 7, custom grip work.

This is an all time favorite board. It is one of my top choices for TS or Hybrid courses. Gotta have the Arizona flag on each of my boards, this one included.

_________________
adam trahan
SlalomSkateboarder.com

<font size=-1>[ This Message was edited by: adam trahan on 2002-09-10 20:28 ]</font>
Adam Trahan
Phoenix, AZ, USA
Phoenix, AZ, USA
 
Posts: 795

Postby Martin Drayton » Fri Sep 27, 2002 6:15 am

I have a few photos of my Turner quiver as it stood at the atart of this summer...It has changed a little, but only in the truck/wheel department. Cambrias now feature heavily and TTC's (wide) are on the rear of my XL, with Extracks on the front. The Indy/Indy offset combo is on the Fullnose, but may get swopped for the Racetrack-X/TTC combo on the Hybrid...
http://www.milleniasystems.co.uk/PicHom ... frame.html

Martin
Martin Drayton
Gecko Decks
Gecko Decks
 
Location: Park City,Utah!
Posts: 732

Postby ur13 » Sat Sep 28, 2002 4:19 am

To check out what team turner is riding (and how they are setup) check ou the "team" section of the turner site. Most riders have a "slalom quiver" link which will show you exactally what they ride and how it is setup.
ur13
 
Posts: 3

Postby Bob Frias » Sat Oct 05, 2002 10:42 pm

Here are my 2 favorite Turners these days. The set-ups are a bit different and definitely feel different due to wheelbase and flex.

First up is my early 90's 2tone cut-away med/stiff. Small pivot Fultrack up front weged out. Small pivot offset on the back wedged forward. This board rides like it's on rails and is very hard on wheels. Wheelbase is 18 1/4 from inner truck mount to inner truck mount. True wheelbase is 20 inches on center.
Image
Image

My NEW red Fulnose med/stiff has a small pivot Fultrack on the front wedged out. Back is a TTC that is wedged forward. Wheelbase is 17 1/8 inner truck mount to inner truck mount. True wheelbase is 19 1/2 inches on center.
Image
The black & Green is great for TS and Hybrid while the Fulnose is a TS monster only. PT Ceramics are all I use for bearings and I'm running those Sure Grip cushions on both back trucks. The blue in 93a for the Fultracks and the yellow in 89a for the TTC.

_________________
Still skatin, after all these years.
Bob Frias
BoBo
BoBo
 
Location: Baltimore,
Posts: 63

Postby Aaron Morris » Fri Apr 25, 2003 2:44 am

I just received my new 2003 Turner Fullnose Deck! Thank you so much Peggy!

Aaron Morris

Team Turner
Aaron Morris
 
Location: Virginia Beach - Norfolk, Virginia
Posts: 90


Return to Turner Summer Ski



cron